Mity CPU Platforms

03/01/2012

08:28 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: about boot

I wonder how the boot mode switch from SPI1 to UART1 using EXT_BOOT# signal? Thank very much. shengyou gao

02/28/2012

08:47 AM MityDSP-L138 (ARM9 Based Platforms) PCB Development: FPGA no-connects for 45 size FPGA on MityDSP-L138F

(Posted on behalf of a customer)
We have done a design using the MityDSP-L138F SOM. I tried avoiding using the pin... Thomas Catalino

02/22/2012

05:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Hello World Starter Guide Permission Issue

You rock! It was the file that was the problem. I found the executable and it worked. Thanks! Tim Eastham

04:50 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Hello World Starter Guide Permission Issue

Hi Tim,
First, the reason you're getting the "-sh: ./hello.o: Permission denied" error is because the file you are... Gregory Gluszek

04:25 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Hello World Starter Guide Permission Issue

I am a newbie to the arm environment and quite green on linux as well. I have been going through the hello world exa... Tim Eastham

02/16/2012

08:03 PM MityDSP-L138 (ARM9 Based Platforms) PCB Development: MityDSP-L138F Footprint Question

(posted on behalf of a customer)
For the MityDSP-l138F, I noticed the drill hole for the standoff in the Altium f... Thomas Catalino

02/14/2012

03:24 PM ARM9 Based QNX Platforms Software Development: RE: Running SYS/BIOS on the ARM MityDSP-L138 module

Dave,
I've been over on the e2e forum for a couple weeks getting our current DSP
running on the OMAP137. TI h... Anonymous

03:14 PM ARM9 Based QNX Platforms Software Development: RE: Running SYS/BIOS on the ARM MityDSP-L138 module

This is something that we haven't done yet.
TI has some info on this: here are some links that may be worth explor... Dave Stehlik

11:21 AM ARM9 Based QNX Platforms Software Development: Running SYS/BIOS on the ARM MityDSP-L138 module

Hi,
I'm currently using a Spectrum Digital's OMAP-L137 eval board to run some older DSP code and I'd like to ... Anonymous

02/08/2012

11:51 AM MityDSP (TI TMS320C6xxx Based Products) PCB Development: RE: AUX I/O Connector location dimensions

Thanks Mike,
I have Rev 1/Document Revision: Draft – MityDSP-Pro Rev. B dated Nov 15th 2009 of the design guide an... Douglas Beumeler

10:58 AM MityDSP (TI TMS320C6xxx Based Products) PCB Development: RE: AUX I/O Connector location dimensions

Hi Doug, dorry for the delay.
The information you need should be in the MityDSP-Pro Carrier board design guide, I ... Michael Williamson

10:48 AM MityDSP (TI TMS320C6xxx Based Products) PCB Development: RE: AUX I/O Connector location dimensions

I would like to get a reply to my question. I am finishing up my layout and need to place the connector.
Thanks,
... Douglas Beumeler

02/06/2012

08:17 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: AXI Compatibility?

(posted on behalf of a customer for the MityARM-1808F module)
Any advice on how to connect your EMIF interface to... Thomas Catalino

02/03/2012

04:46 PM MityDSP (TI TMS320C6xxx Based Products) PCB Development: AUX I/O Connector location dimensions

It is recommended to use the AUX I/O connector on the MityDSP-Pro on carrier board designs but I can't seem to find a... Douglas Beumeler