Activity
From 04/30/2014 to 05/29/2014
05/29/2014
- 04:29 PM Software Development: RE: How to run bin application via u-boot?
- Ahmed,
I believe Mike was suggesting that you build the application as a "release" version without any debugging a... - 04:04 PM Software Development: RE: How to run bin application via u-boot?
- Just to confirm, you have the compiler option "--symdebug:none" in your release compile and link options?
-Mike
- 03:51 PM Software Development: RE: How to run bin application via u-boot?
- Hi Mike,
I have tried what you mentioned and it didn't work.
I'll wait your trial.
Thanks in advance. - 03:02 PM Software Development: RE: How to run bin application via u-boot?
- I think you need to strip the .out file (make a release version that removes the debugging information).
If I get ... - 01:48 PM Software Development: RE: How to run bin application via u-boot?
- Posting some previous direct followup e-mails from the customer.
I have followed the steps of the Starterware wiki... - 10:47 AM Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Hi,
Can you please capture the entire boot up on the console to a text file and set it over?
Or at least run "u... - 10:38 AM Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Dear Bob,
when I try to load the modules with "insmod fpga_ctrl.ko" I get an error with "Function non implemented"... - 09:30 AM Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Hi Silvano,
Jon was referring to the kernel modules explicitly. The modules need to be installed in your target ro... - 08:47 AM Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- I report before that I recompile the kernel every time I made a modificatuon on the baseboard file.
In fact the link... - 08:24 AM Software Development: RE: Kernel loading module problems MityDSP and FPGA configuration
- Its hard to tell from those error messages whats going on but have you tried recompiling the kernel modules when you ...
- Hello everybody.
I am Silvano Bertoldo, I mainly work on the software side of MityDSP and I have a big problem abo... - 09:53 AM Software Development: RE: Compiler does not run in VM
- Also our vm does come with the toolchain installed. I'm unsure why you were unable to locate it.
Try looking in /u... - 09:29 AM Software Development: RE: Compiler does not run in VM
- Yes. You need to run the 32-bit version in the VM if your VM is a 32-bit architecture.
on your VM type "uname -a".... - Hello- I'm new to the MityDSP platform and I am having trouble getting the development environment working. I have i...
05/28/2014
- Hi everyone,i have MityARM1808F.
I could use "bootelf" command[ex: bootelf 0xc0700000] to run any app.out,but the si... - 08:54 AM Software Development: RE: UPP ISR is not called
- Finally i could solve this issue by adding the following code :
asm(" mrc p15, #0, r0, c1, c0, #0\n\t"
" ...
05/19/2014
- 04:43 PM FPGA Development: RE: Programming FPGA Flash using IMPACT
- Thanks Michael,
I shall follow the steps in the link you mentioned and let you know results.
05/17/2014
- 12:45 PM Software Development: RE: DSP- EDMA Transmission problem
- Hello again,
I am now trying to transmit data using upp interface. On the FPGA- side the interface works correctly, ...
05/16/2014
- 05:55 PM Software Development: RE: EMIF Clock in U-Boot
- Hello,
I assume you mean the EMIFA clock (to FPGA) not the EMIF clock (used for the DDR).
I am sorry I missed t...
05/15/2014
- 08:36 PM FPGA Development: RE: Programming FPGA Flash using IMPACT
- Hi,
Please take a look at the [[Programming the FPGA]] wiki page for information about programming the FPGA.
Th...
05/14/2014
- Hi everyone,
I'am using CCS V5.3 and emulator XDS100V2.
I have developed SYS/BIOS ARM app. which use UPP to se...
05/12/2014
- 11:44 AM PCB Development: RE: uPP Interface
- I don't think that the UPP pins are pinmuxed (there is only one option if the UPP is used). See the MDK/sw/dsp/core/...
- 09:16 AM PCB Development: RE: uPP Interface
- Thanks Mike for reply.
The question will be, to what pins DSP connected pins FPGA? It needs to be known for purpos... - 07:08 AM PCB Development: RE: uPP Interface
- The UCF file in the board support package at MDK/fpga/vhdl/MityDSP_L138.ucf includes connection information between t...
- Hi,
How to find out as are connected pins FPGA and DSP for the interface uPP?
Kind Regards,
Oleh
05/11/2014
- 01:03 PM FPGA Development: RE: UPP Sample Code needed
- Thanks for you.That really helps.
- Hello everyone, i have a MityARM-1808F with 256-Mb NAND Flash.
1 - I need to know the steps to Program FPGA Flash ...
05/09/2014
- 10:24 AM Software Development: RE: DSP DMA crashes Linux
- I have recently been working on a project where we ran into conflicts between QDMA's on the DSP side and MMC use on t...
05/08/2014
- 08:39 AM PCB Development: RE: 3D Step (STP) Files
- Hi,
Please check this "wiki page":https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/CAD_Files ... - Hi There,
Would it be possible to make available a 3D STP file of the MityDSP L138F
processor module for mechani...
05/02/2014
- 03:53 PM Software Development: RE: DspFpgaGpio.cpp: i f (Bank > mnNumBanks) return -1
- Hi John,
You are correct. We've pulled in this fix and it will get published in the next release for the MityDSP-... - FYI.
In tcDspFpgaGpio::ConfigurePin(unsigned int Bank, unsigned int Offset, etc.) and a few other fctns in DspFpga...
Also available in: Atom
Go to top
