Activity

From 10/19/2023 to 11/17/2023

MA 07:38 PM PCB Development: RE: Pin connection: Thanks for your reply, Mike. I used Y13 as the clock pin in the development board and I wonder where internally in the layout of the development kit it is connected.
I want to remove just the FPGA module and use it alone in my project... Mohammad Hassan Adeli
MW 07:30 PM PCB Development: RE: Pin connection: Hi Mohammad,
If you open up the Datasheet and check Table 8 and search for Y13 you should that it is a direct connect to the EDGE connector (I believe pin 117, but you should double check).
There is no other connection.
With reg... Michael Williamson
MA 07:08 PM PCB Development: Pin connection: Hello,
I have a development kit of MitySOM-5csx (https://www.criticallink.com/product/mitysom-5csx-dev-kit/). I was wondering can anyone let me know where the Y13 pin of the FPGA module is connected internally in this board.
Thank... Mohammad Hassan Adeli

AB 06:18 PM MitySOM-5CSX Embedded Vision Developer's Kit for Basler dart BCON Support: RE: Barrel jack type: Marko,
The manufacturer part number used for the barrel jack is PJ-059BH. I have attached the manufacturer datasheet for your reference which has the dimensions you should need.
Alex Alexander Block
MM 07:28 AM MitySOM-5CSX Embedded Vision Developer's Kit for Basler dart BCON Support: Barrel jack type: Hello,
I was wondering if you could help me find information on the specifications for the barrel plug, we need the size of the inner pin and the radius of the barrel. Marko Mamić
MA 03:02 PM FPGA Development: Clock frequency pins: Hello,
We have this module (https://www.criticallink.com/product/mitysom-5csx/ ) board on our project board and also I have this development kit with the same controller (https://www.criticallink.com/product/mitysom-5csx-dev-kit/).
... Mohammad Hassan Adeli

DR 02:35 AM PCB Development: RE: MSEL[4] and return current cap...: Sorry if I wasn't clear. The caps are optional. They might help in a worst case situation, but for most designs they are overkill. Leaving one off won't be a problem. If you are doing a design and have the option to put them on, it w... David Rice

AF 11:34 PM PCB Development: RE: MSEL[4] and return current cap...: Hi David,
I understand that, but the eval board only has them on MSEL[3:0] and does not have one on MSEL[4]. So, should there be one on MSEL[4] on any design using the MitySOM or not?
Thanks,
Austin Austin Franklin
DR 07:38 PM PCB Development: RE: MSEL[4] and return current cap...: The intention of the caps to ground on these signals is to allow some high frequency ground currents from the SOM I/O's going off-SOM to have additional paths to ground, since the MSEL signals (and other listed signals) are essentially D... David Rice

AF 06:54 PM PCB Development: MSEL[4] and return current cap...: The dev board has MSEL[3:0] with 1000pF caps, and MSEL[4] does not have a cap, unless I missed it. In the design guide:
7.4 Return Currents
The module’s edge connector has GND connections distributed along the interface pinout to ma... Austin Franklin

DV 06:10 PM FPGA Development: RE: Link missing on System Design Overview wiki page: Thank you for bringing this to our attention, I've updated the text on that wiki page so it now links to our reference project.
Dan Daniel Vincelette

SA 08:00 PM Software Development: RE: How to boot FPGA from U-Boot without having the uboot.env file in my SD card: Hi everyone,
For anyone who is reading, I have figured it out and I hope this will help you.
The U-Boot is running a script, see the bootcmd below Shahad Alrawi
TC 02:24 AM FPGA Development: Link missing on System Design Overview wiki page: (posted on behalf of a customer)
on this URL:
https://support.criticallink.com/redmine/projects/mityarm-5cs/wiki/System_Design_Overview
it says:
"Create a new project or start from the Critical Link MityARM-5CSX reference pro... Thomas Catalino

AF 06:54 PM PCB Development: RE: Standoff on Mounting Hole Locations page: Part number 91115A501 is a 3/8" size standoff (1/8" tall, 4-40, hex). The one on the deb board I have is 1/4" size, which is part number 91115A160.
https://www.mcmaster.com/catalog/129/3674/91115A160
Austin Franklin

SA 10:38 PM Software Development: RE: How to boot FPGA from U-Boot without having the uboot.env file in my SD card: Hello,
I was wondering, I found in u-boot-socfpga/include/configs Shahad Alrawi
SA 12:18 PM Software Development: How to boot FPGA from U-Boot without having the uboot.env file in my SD card: Hello,
As a follow up from this question:https://support.criticallink.com/redmine/boards/45/topics/6501
Luckily, I was able to compile U-Boot 2019 from your CriticalLink repo and compile the Linux kernal and Yocto Rootfs as specifi... Shahad Alrawi

Also available in: Atom

Mity CPU Platforms » MitySOM-5CSX Altera Cyclone V