Activity
From 01/03/2017 to 02/01/2017
01/31/2017
- AB 06:48 PM MityDSP-L138 (ARM9 Based Platforms) PCB Development: RE: FPGA CLOCK LOCATION
- Alex,
Thank you for reaching out to us about this question.
On our MitySOM-L138F family modules we have the EMIF bus from the OMAP-L138 connected to the Xilinx Spartan 6 FPGA to allow for communications of cores between the process...
01/30/2017
- Hello good day I developing a new project in ISE WEBPACK using the PROFIBUS DEVELOPMENT KIT with the MitySOM-1810F Processor Card.
I am programming the FPGA and this is my entity:
PORT(
*CLK50* : IN STD_LOGIC;
RX : IN STD_LOG...
01/23/2017
- JA 10:59 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA - Loading via CPU
- Hello, good day
I load the FPGA with "Example loading the .bin file over the serial port using Kermit" because it was easier but I will continue trying with TFTP server.
U-Boot > loadb 0xC0700000
## Ready for binary (kermit) ... - MW 06:58 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SATA link down
- Are you using SATA-II or SATA-III link speeds? I believe the Errata from TI still applies.
01/22/2017
- FX 10:37 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: SATA link down
- hello ,I have the same problem !
Can you tell me this problem is Finish or not?
01/20/2017
- JC 01:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA - Loading via CPU - "ERROR LOADING"
- Jesus Alejandro Alvarez Trejo wrote:
> Hello, Good Day
> ...
Your ping command was run while booted into linux. You should run it while in u-boot to prove you have network communication working.
>
> ...
What tftp server are you usi... - JA 12:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA - Loading via CPU - "ERROR LOADING"
- Hello, Good Day
I am trying to load the FPGA using https://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Programming_the_FPGA vía CPU, I already created the .bin file to do the first test. I am using the ...
01/16/2017
- AB 05:17 PM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD
- Ben,
Thank you for providing the device specific details.
I wanted to let you know that on Friday 1/13/2017 I sent you an e-mail requesting additional company specific information, that I wasn't sure you would want to post on the f...
01/13/2017
- BF 08:44 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD
- Thanks. Today we tested two kits against each other (we switched the DevKit and modules). The results were, that the development boards were OK, but one Cyclone V SOC module (this was mine) is not booting. The orange LED is permanently O...
- MW 07:52 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD
- Hi Benjamin,
I am forwarding this on to our support team, but it sounds like there may be an issue with the DevKit card or module. If I understand, you are able to use the same SD card on different units and some units work and this ... - BF 07:35 AM MitySOM-5CSX Altera Cyclone V Software Development: RE: 5CSX-H6-42A Dev.Kit does not boot from SD
- On other devices my image is working... It seems that I got a newer module (noticed some small differences on the PCB). ID: 5CSXFC6C6U23I7N
01/12/2017
- JC 02:41 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA - Loading via CPU
- I don't understand the difference between this question and your last question. https://support.criticallink.com/redmine/boards/10/topics/5138
The programming guide from which you grabbed the above paragraph, includes the two ways tha... - Hi, Good Day, I am trying to load the FPGA via CPU, but I would like to know: How can I configure the slave select mode in the FPGA?. I read the Xilinx Spartan-6 configuration guide, but it is not enough clear.
"The FPGA has been con... - Hello, Good Day, I have the MitySOM-1810F PROFIBUS Development kit which includes the AM1810 ARM Microprocessor For PROFIBUS and Spartan 6, I would like to know how I can communicate both devices, I mean, what kind of protocol and how im...
- MW 11:08 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Programming the FPGA
- Take a look at the [[Programming the FPGA]] for information about programming the FPGA. The wiki page on this web site has a bunch of information to get started.
If you want to program with JTAG via a Xilinx emulator pod, you can do ... - Hello, Good Day, I have the MitySOM-1810F PROFIBUS Development kit, I am starting to use it and I do not know how load the FPGA, I would like to know if I need a special connector or if I could use other method to load the FPGA.
- Hi guys,
this struggles me for a few days now. I got the mentioned Dev-Kit, read a lot in Rocketboards and this Wiki, and so I wanted to try it out by myself.
So I installed the virtual-machine, compiled my Preloader and U-Boot to c...
01/08/2017
- When trying to access wiki and forums i get
An error occurred during a connection to support.criticallink.com. The OCSP server suggests trying again later. Error code: SEC_ERROR_OCSP_TRY_SERVER_LATER
The page you are trying to...