Activity

From 08/12/2011 to 09/10/2011

04:45 PM Software Development: RE: IndustrialLO.bin: Hi Scott,
Yes, the IndustrialIO.bin file distributed in the MDK has the base module and other cores built in and y... Gregory Gluszek
04:01 PM Software Development: IndustrialLO.bin: Hello,
I am working with writing drivers to access FPGA registers on the EMIFA. I currently don't have any custom... Scott Whitney

04:29 PM Software Development: RE: no serial data when first using dev kit: Mike -
Glad you are up and running. Good point about the out of box experience.
Thanks,
Tom Thomas Catalino
04:25 PM Software Development: RE: no serial data when first using dev kit: Hi Greg,
That was it! I did not use the cable supplied because I always have serial cables connected to my comput... Mike Costa
04:20 PM Software Development: RE: no serial data when first using dev kit: Hi Mike,
J502 is the default RS232 port and the ribbon cable is meant to be used on this port for RS232 communicat... Gregory Gluszek
04:11 PM Software Development: no serial data when first using dev kit: Hi,
I am just starting to get my Dev kit up and running with the L138f Module. I am used to the Embedded Linux d... Mike Costa

06:50 PM FPGA Development: RE: Xilinx ISE Design Suite 13.2 and MDK_2011_08_01: Hi Mike,
The files it was getting stuck on were ads7843.vhd, i2c.vhd, lcd_ctlr.vhd and tfp410.vhd.
However, I made... Keith Fletcher
07:08 AM FPGA Development: RE: Xilinx ISE Design Suite 13.2 and MDK_2011_08_01: The project and NGC files were built with ISE 12.3. We will be migrating the 13.x in the next release cycle.
Whic... Michael Williamson
12:34 AM FPGA Development: Xilinx ISE Design Suite 13.2 and MDK_2011_08_01: Hi,
I have just downloaded the windows version of Xilinx ISE Design Suite 13.2 and attempted to build the examples I... Keith Fletcher

09:02 PM Software Development: RE: u-boot prompt from kernel possible ?: Hi Thomas,
From linux, if you issue the "reboot" command, it will jump back to u-Boot.
The bootdelay variable (... Michael Williamson
06:21 PM Software Development: u-boot prompt from kernel possible ?: Hi,
Once the kernel is loaded and we are logged in, is there a way to restart and bring the card to U-boot> prompt w... Thomas Nagel

03:12 PM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: What modules are missing exactly? In the kernel menuconfig you can elect to "Enable loadable module support" and then... Gregory Gluszek
02:51 PM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: Thank you. I downloaded Tera Term and it worked !
sorry to bother you - one last question. I noticed that after kern... Thomas Nagel
11:42 AM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: What program are you using for terminal access?
I just tested with Tera Term Professional Version 4.57, using the ... Gregory Gluszek
11:20 AM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: Thank you. I built the image according to instructions (added USB storage support)
http://support.criticallink.com/r... Thomas Nagel

01:40 PM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: You will need to rebuild the kernel (and install it on your system) such that it supports USB mass storage devices an... Michael Williamson
01:33 PM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: Thank you very much for the information. After using USB 1.1 port as host port, connecting a USB flash drive, I have ... Thomas Nagel
07:29 AM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: USB support for the OMAP-L138 is fully described in the User Guides provided by the TI on it's "OMAP-L138 Processor":... Michael Williamson

03:33 PM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: Hi,
USB stick is not connected. It is a USB cable only.
The configuration is like this :
UART to USB via FT23... Thomas Nagel
02:46 PM Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?: Can you provide a reference schematic to your baseboard?
Do you have a USB memory stick connected to one of the tw... Michael Williamson
02:16 PM Software Development: Transfer files to card from PC via usb ? instead of ethernet ?: Hi,
I have two USB cables connected to baseboard.
Using one, I am able to connect to console and login root@mit... Thomas Nagel

06:33 PM Software Development: RE: MityDSP GUI: Thanks for the reply. Sorry for the confusion.
We have our own baseboard with mitydsp connected to it. Using UART t... Thomas Nagel
12:53 PM Software Development: RE: MityDSP GUI: Hi Thomas,
I'm a little confused. The MItyDSP-L138 card is a "system on module (SOM) or computer on module (COM) ... Michael Williamson
12:41 PM Software Development: RE: MityDSP GUI: Hi Mike, Thanks for the reply. We do not have the baseboard. Only the mitydsp-l138 card. Can we still communicate wit... Thomas Nagel
07:33 AM Software Development: RE: MityDSP GUI: The Industrial I/O card (the MityDSP-L138 development kit baseboard) should have come with a 10 pin ribbon to DB-9 co... Michael Williamson

05:08 PM Software Development: RE: MityDSP GUI: Yes, we have OMAPL138 product. Is there a user interface that works with this card ?
We are trying to use UART inter... Thomas Nagel
05:02 PM Software Development: RE: MityDSP GUI: Hi Thomas -
The MityDSP GUI is used only with our 6711 and 6455 based product. I believe you have an OMAPL138 or ... Thomas Catalino
04:58 PM Software Development: MityDSP GUI: Hi,
Is the MityDSP GUI , part of hardware shipment ? or do we have to buy it separately ? Can I download it from cri... Thomas Nagel
02:43 PM Software Development: RE: Eclipse CDT Builder problem when set up for cross compile: Fred,
There's a good chance that your bashrc file is no being read when you start it from the launcher. I don't reme... Tim Iskander
02:35 PM Software Development: RE: Eclipse CDT Builder problem when set up for cross compile: The angstrom environment-setup script is run at the end of my .bashrc file.
Running Eclipse from a shell known to ... Fred Weiser
01:50 PM Software Development: RE: Eclipse CDT Builder problem when set up for cross compile: Hi Fred,
Where are you running the angstrom environment-setup script? We typically add this to the end of our bash... Gregory Gluszek
01:36 PM Software Development: Eclipse CDT Builder problem when set up for cross compile: Hi.
I am getting the following error when attempting to build a project in Eclipse. I am not using CL's VM - my Ec... Fred Weiser

07:07 AM FPGA Development: RE: 372 MHz: Hi Rob,
In general, running at different EMIFA bus rates should be OK as long as you keep in mind the following po... Michael Williamson

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)