Project

General

Profile

Activity

From 11/10/2014 to 12/09/2014

12/09/2014

06:06 AM Software Development: DSP/BIOS issue MityDSP-L138
Hi,
Why at programming port UART-1 under a DSP/BIOS (from DSP side) in reply to sending of a binary file on the hy...
Oleh Mela

12/08/2014

04:58 PM Software Development: RE: mtd->read() returned ECC error
You may have better luck with the latest MDK. MDK_2014-01-13 is the newest.
Download release_2014-01-13.run fro...
Jonathan Cormier
04:52 PM Software Development: RE: mtd->read() returned ECC error
MDK_2011-03-31
Chris Coonan
04:51 PM Software Development: RE: mtd->read() returned ECC error
Which MDK version? Jonathan Cormier
04:48 PM Software Development: RE: mtd->read() returned ECC error
I am using the mityomap-full.jffs2 supplied with the MDK. I "assumed" the filesize was the number of bytes transferre... Chris Coonan
04:44 PM Software Development: RE: mtd->read() returned ECC error
Chris,
Your flash commands seem reasonable though it is unusual that your file happens to already be exactly 0x800...
Jonathan Cormier
03:56 PM Software Development: mtd->read() returned ECC error
I know this issue was addressed earlier in this forum. I followed the instructions given regarding the need to use th... Chris Coonan

11/24/2014

09:23 AM Software Development: RE: inotify issue
This is a non-problem. It is working fine. Sorry for the trouble. Chris Coonan
09:12 AM Software Development: RE: inotify issue
Could you provide some example code that shows the problem you are having? Also need a better explanation of what pro... Jonathan Cormier
07:31 AM Software Development: RE: inotify issue
My mistake. Cut and paste error. The kernel is 2.6.34-RC1.
Chris Coonan

11/22/2014

12:09 PM Software Development: inotify issue
Trying to get inotify to execute properly from inside my application code. I am using linux kernel 2.24-RC1.
Are t...
Chris Coonan

11/17/2014

05:16 PM Software Development: RE: FPGA configuration via u-Boot problem
You can also use the promgen command to generate a bin file from a bit:
promgen -w -p bin -u 0 filename.bit -o fil...
Gregory Gluszek
07:29 AM FPGA Development: RE: PlanAhead issue
For ISE (and I think ISE / PlanAhead are still the tools for Spartan 6, as the Vivado tools are for 7 series and high... Michael Williamson
03:21 AM FPGA Development: PlanAhead issue
Hi,
Why at creation of the project in PlanAhead 14.7 for the chip xc6slx45csg324-3 it is not possible to specify Tem...
Oleh Mela

11/14/2014

07:51 AM Software Development: RE: FPGA configuration via u-Boot problem
Hey,
I solved the problem.
It's important that the FPGA config file <fpga>.bin file was created correctly.
By...
Stefan Krassin
07:30 AM Software Development: FPGA configuration via u-Boot problem
Hi all,
I have a problem with the configuration of the FPGA and booting linux.
I followed the instructions from...
Stefan Krassin

11/10/2014

01:52 PM Software Development: RE: Real time SATA writes
Hi Mary,
As you suspected in your original post, it is likely that when you are calling fwrite, in some cases the ...
Dominic Giambo
01:04 PM Software Development: RE: Real time SATA writes
After further testing and setting optimization, I have narrowed down the delay:
The call to fwrite() normally take...
Mary Frantz
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)