Mity CPU Platforms

09/12/2011

02:47 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: ymodem

Hi,
What is a better option to upload a file (uImage for example) at U-boot prompt ?
When ymodem transfer fails, u-... Thomas Nagel

09:15 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: Unable to build root file system

Hi Mike,
I was trying to build the root file system using the instructions on the wiki but getting lot of errors. ... Noman Siddiqui

09/09/2011

04:45 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: IndustrialLO.bin

Hi Scott,
Yes, the IndustrialIO.bin file distributed in the MDK has the base module and other cores built in and y... Gregory Gluszek

04:01 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: IndustrialLO.bin

Hello,
I am working with writing drivers to access FPGA registers on the EMIFA. I currently don't have any custom... Scott Whitney

09/08/2011

04:29 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: no serial data when first using dev kit

Mike -
Glad you are up and running. Good point about the out of box experience.
Thanks,
Tom Thomas Catalino

04:25 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: no serial data when first using dev kit

Hi Greg,
That was it! I did not use the cable supplied because I always have serial cables connected to my comput... Mike Costa

04:20 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: no serial data when first using dev kit

Hi Mike,
J502 is the default RS232 port and the ribbon cable is meant to be used on this port for RS232 communicat... Gregory Gluszek

04:11 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: no serial data when first using dev kit

Hi,
I am just starting to get my Dev kit up and running with the L138f Module. I am used to the Embedded Linux d... Mike Costa

09/01/2011

06:50 PM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Xilinx ISE Design Suite 13.2 and MDK_2011_08_01

Hi Mike,
The files it was getting stuck on were ads7843.vhd, i2c.vhd, lcd_ctlr.vhd and tfp410.vhd.
However, I made... Keith Fletcher

07:08 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: RE: Xilinx ISE Design Suite 13.2 and MDK_2011_08_01

The project and NGC files were built with ISE 12.3. We will be migrating the 13.x in the next release cycle.
Whic... Michael Williamson

12:34 AM MityDSP-L138 (ARM9 Based Platforms) FPGA Development: Xilinx ISE Design Suite 13.2 and MDK_2011_08_01

Hi,
I have just downloaded the windows version of Xilinx ISE Design Suite 13.2 and attempted to build the examples I... Keith Fletcher

08/31/2011

09:02 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: u-boot prompt from kernel possible ?

Hi Thomas,
From linux, if you issue the "reboot" command, it will jump back to u-Boot.
The bootdelay variable (... Michael Williamson

06:21 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: u-boot prompt from kernel possible ?

Hi,
Once the kernel is loaded and we are logged in, is there a way to restart and bring the card to U-boot> prompt w... Thomas Nagel

08/22/2011

03:12 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

What modules are missing exactly? In the kernel menuconfig you can elect to "Enable loadable module support" and then... Gregory Gluszek

02:51 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

Thank you. I downloaded Tera Term and it worked !
sorry to bother you - one last question. I noticed that after kern... Thomas Nagel

11:42 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

What program are you using for terminal access?
I just tested with Tera Term Professional Version 4.57, using the ... Gregory Gluszek

11:20 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

Thank you. I built the image according to instructions (added USB storage support)
http://support.criticallink.com/r... Thomas Nagel

08/19/2011

01:40 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

You will need to rebuild the kernel (and install it on your system) such that it supports USB mass storage devices an... Michael Williamson

01:33 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

Thank you very much for the information. After using USB 1.1 port as host port, connecting a USB flash drive, I have ... Thomas Nagel

07:29 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

USB support for the OMAP-L138 is fully described in the User Guides provided by the TI on it's "OMAP-L138 Processor":... Michael Williamson

08/18/2011

03:33 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

Hi,
USB stick is not connected. It is a USB cable only.
The configuration is like this :
UART to USB via FT23... Thomas Nagel

02:46 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Transfer files to card from PC via usb ? instead of ethernet ?

Can you provide a reference schematic to your baseboard?
Do you have a USB memory stick connected to one of the tw... Michael Williamson

02:16 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Transfer files to card from PC via usb ? instead of ethernet ?

Hi,
I have two USB cables connected to baseboard.
Using one, I am able to connect to console and login root@mit... Thomas Nagel

08/17/2011

06:33 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: MityDSP GUI

Thanks for the reply. Sorry for the confusion.
We have our own baseboard with mitydsp connected to it. Using UART t... Thomas Nagel

12:53 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: MityDSP GUI

Hi Thomas,
I'm a little confused. The MItyDSP-L138 card is a "system on module (SOM) or computer on module (COM) ... Michael Williamson

12:41 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: MityDSP GUI

Hi Mike, Thanks for the reply. We do not have the baseboard. Only the mitydsp-l138 card. Can we still communicate wit... Thomas Nagel

07:33 AM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: MityDSP GUI

The Industrial I/O card (the MityDSP-L138 development kit baseboard) should have come with a 10 pin ribbon to DB-9 co... Michael Williamson

08/15/2011

05:08 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: MityDSP GUI

Yes, we have OMAPL138 product. Is there a user interface that works with this card ?
We are trying to use UART inter... Thomas Nagel

05:02 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: MityDSP GUI

Hi Thomas -
The MityDSP GUI is used only with our 6711 and 6455 based product. I believe you have an OMAPL138 or ... Thomas Catalino

04:58 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: MityDSP GUI

Hi,
Is the MityDSP GUI , part of hardware shipment ? or do we have to buy it separately ? Can I download it from cri... Thomas Nagel

02:43 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Eclipse CDT Builder problem when set up for cross compile

Fred,
There's a good chance that your bashrc file is no being read when you start it from the launcher. I don't reme... Tim Iskander

02:35 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Eclipse CDT Builder problem when set up for cross compile

The angstrom environment-setup script is run at the end of my .bashrc file.
Running Eclipse from a shell known to ... Fred Weiser

01:50 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: RE: Eclipse CDT Builder problem when set up for cross compile

Hi Fred,
Where are you running the angstrom environment-setup script? We typically add this to the end of our bash... Gregory Gluszek

01:36 PM MityDSP-L138 (ARM9 Based Platforms) Software Development: Eclipse CDT Builder problem when set up for cross compile

Hi.
I am getting the following error when attempting to build a project in Eclipse. I am not using CL's VM - my Ec... Fred Weiser