Activity
From 05/28/2012 to 06/26/2012
06/26/2012
- 09:34 PM FPGA Development: RE: What‘s the configuration mode of the FPGA?
- Thanks very much.
- 08:58 AM FPGA Development: RE: What‘s the configuration mode of the FPGA?
- Hello Mr. Lu,
The FPGA is configured using 8 bit parallel slave select mode via the EMIFA bus connection to the Om... - 10:29 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Charlie -
Thanks for the update, great news!
Tom - 09:48 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I have finally got the switch to work. The last problem was that I had set the CONF0-CONF2 bits to 0x110, whi...
06/25/2012
- Hello,
We are using the MityDsp-L138F board. I want to know the FPGA's configuration mode on the board, is it MAS...
06/20/2012
- 07:14 AM Software Development: RE: Building new openembedded-core based system from scratch
- At the moment, we cannot expose the full repository as there is proprietary data stored in it.
We need to work wit...
06/19/2012
- 11:55 PM Software Development: RE: Can't ping by name
- Hello, Mattias!
I have installed resolvconf package after reading your post. Anyway /etc/resolv.conf still beeing em...
(posted on behalf of a customer)
I would like to build a dev environment from scratch if possible and am follo...
06/18/2012
- 09:20 AM Software Development: RE: Can't ping by name
- I think the dns-* options in /etc/network/interfaces require that you have the resolvconf package installed. Do you h...
- 01:51 AM Software Development: RE: Can't ping by name
- Solved! Thank you!
The only disadvatage is the /etc/resolv.conf file is rewritten (by udhcpc?) on reboot.
I wonder...
06/15/2012
- 07:30 AM Software Development: RE: Can't ping by name
- We've noticed that the DNS doesn't get updated automatically as well.
If you know your DNS server, as a workaround... - Hello!
Problem is I can't ping any host by name (got "bad address" error), but no problem with ping by IP. I guess i...
06/14/2012
- 08:09 AM Software Development: RE: The Jtag Interface
- If you need more or you did not buy the development kit, the part number for the interface is 80-000286LC-1A. If you...
06/13/2012
- 05:19 PM PCB Development: RE: MityDSP-L138F Footprint Question
- 20mils is a mechanical tolerance for DDR2 connector placement
- 02:10 PM PCB Development: RE: The schematic of MityDSP-L138 Development Kit
- Actually, the schematics for the baseboards may be found here:
"Industrial I/O Revision Information":http://suppor... - 12:44 PM PCB Development: RE: The schematic of MityDSP-L138 Development Kit
- Hello Yilin -
I will e-mail you a link to download the design files for the MityDSP-L138 base board.
Thank yo... - (posted on behalf of a customer)
which voltage level your EMIFA-Pins are configured? Is it 1,8V or 3,3V? - 09:23 AM Software Development: RE: Downloading and Installing the Virtual Machine?
- The Wiki page (http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Linux_Build_VM) has been updated ...
- 06:31 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I am using mii-tool to test that mii interface. I have used ths before with no problem, but now I get a linux... - 04:47 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
Thanks for that. Now the spi interface works (but not the switch). I now get the following at boot up.
Mic... - 06:14 AM Software Development: RE: The Jtag Interface
- The development kit comes with a small adapter board that connects to the hirose connector on the SOM and provides a ...
06/12/2012
- 10:49 PM Software Development: RE: Downloading and Installing the Virtual Machine?
- Me too. I am still interested a link to the new image.
- 10:35 PM Software Development: RE: Downloading and Installing the Virtual Machine?
- Hi, mike
Can you post the link to me?
thanks
- The JTAG Interface of MityDSP-L138 is different with my XDS510. There is a convert board for it? How can I use the M...
- I want to design a Carrier Board of MityDSP-L138. The MityDSP-L138 Carrier Board Design Guide is too simple. Where ca...
- 07:19 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Ok Charlie,
You need to do a little more work on your baseboard file. You need to make sure you strip out all of ... - 03:02 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I have attached the .config and a copy of the dmesg with the L138 SOM board plugged into our dev board and al...
06/11/2012
- 08:35 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Hi Carlie,
Can you attach your .config file and the dmesg outputs? The SPI_MAX_CHIPSELECT is a good catch. That ... - 10:35 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I am back on this project after being called to sort some problems out.
I have sorted out the hardware iss... - The attached file contains TI's OMAP-L138 / AM1808 StarterWare package with additional examples for the MityDSP-L138 ...
- The attached UBoot image contains an update to the bootelf command that fixes the problem where bootelf hangs when la...
- 09:51 AM Software Development: RE: SATA HDD problem
- Thanks, Mike. You are right.
- 07:02 AM Software Development: RE: SATA HDD problem
- Looks like the drive you are using is a SATA III (Gen3) Drive. There is an "errata":http://www.ti.com/lit/er/sprz301...
- Hello!
I am trying to connect SATA HDD to Industrial IO devkit, but there is a problem. Boot log:...
06/08/2012
- 03:55 PM PCB Development: RE: RTC 3V BATT Connection when not using RTC?
- Ground it.
-Mike
- (posted on behalf of a customer)
Quick question: hopefully an easy one to answer. If I don’t want to use a battery... - 08:16 AM PCB Development: RE: RTC Battery Drain
- Hi,
There has been an "Errata":http://support.criticallink.com/redmine/projects/arm9-platforms/wiki/Module_Product... - 03:41 AM PCB Development: RE: Adding a SPI peripheral through J700 on industrialIO board
- Hi Mike:
Sorry about the setting of menuconfg, the format is error.
already check are
Debug support for SPI ... - 03:37 AM PCB Development: RE: Adding a SPI peripheral through J700 on industrialIO board
- Hi Mike:
We are designing a spi device under SPI1 and already success create chip select from OMAP GPIO.
But how ...
06/04/2012
- 01:14 PM Software Development: RE: Cannot run multiple times my ARM/DSP application
- Mike,
Thanks for your answer.
Yes, I am already using the ReturnBuffer() method in DSP side.
Also, while pu...
06/02/2012
- 01:01 PM Software Development: RE: Cannot run multiple times my ARM/DSP application
- Hello François,
On the DSP side, if you are using the tcIPCInbound class, are you calling the ReturnBuffer() metho... - 12:52 PM Software Development: RE: Non-FPGA module NAND Timings
- Hi,
Yes, currently the NAND timings are set up in the u-Boot code in line 290 of the file:
u-boot/board/davinci...
06/01/2012
- Hi,
I don't know if somebody has seen this kind of issue. I have a ARM/DSP application based on the "DSP HelloWorl... - (Posted on behalf of a customer)
In the wiki it says that without a FPGA the NAND access changes: "... on the Indu...
05/30/2012
- 04:36 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
Yes, I have only spotted that today, but when I changed the inputs to 0b10, with some difficulty since they a... - 01:34 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Hi Charlie,
I went back and reviewed your hardware design.
It looks like you have PS1 and PS0 floating on your ... - 09:53 AM Software Development: RE: Increasing CPU speed
- Hello Mike,
Some parts of your answer were really helpful and gave me some hints such as I think I can proceed.
... - 08:12 AM Software Development: RE: Increasing CPU speed
- You have both the ARM+DSP running sysbios? Which do you intend to control the CPU speed (they are tied to the same c...
- Hello,
As mentioned in the title, we plan to increase the cpu speed from 300MHz (default) to 456MHz. In a Linux ...
05/29/2012
- 07:50 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Hi Charlie,
I will try to respond tomorrow with details. Ran out of time today. Sorry for the delay.
-Mike
- 10:22 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
Thanks for the suggestions.
1) The line you mention is the line I had to remark out to get the unit to run...
05/28/2012
- 06:20 PM Software Development: RE: KSZ8995MA Ethernet Switch Support
- OK Charlie,
Three things:
1) In the board file, I think you need to configure the emac_pdata->phy_id to "". Th... - 10:41 AM Software Development: RE: KSZ8995MA Ethernet Switch Support
- Mike
I have successfully merged the version 3.4.0+ with the mitydsp-linux-3.2, but i stil can't get the KSZ8995MA ...
Also available in: Atom
Go to top