Activity
From 05/01/2016 to 05/30/2016
05/27/2016
- I'm trying to set up PINMUX5 at address 0x01C14134 to have EPWM1A on the output. It seems to take on the desired value momentarily, but the value subsequently changes back after only a brief moment. The following is the code that I'm using:
05/26/2016
- JC 09:48 AM Software Development: RE: Instructions to get going with the OMAP PWM
- Andrew Bean wrote:
> I'm trying to get EPWM1A running with the MityDSP-L138 module and MityDSP-L138 (F) Family Development Kit.
> ...
I'm not sure if anyone here has used the pwm's on the L138. Looking at the l138 kernel to see if the...
05/25/2016
- I'm trying to get EPWM1A running with the MityDSP-L138 module and MityDSP-L138 (F) Family Development Kit.
1) Is there a set of instructions or any discussion on using the PWM specifically for the MityDSP-L138? All I need is a square wa... - JC 02:53 PM Software Development: RE: Problems with the first time configuration
- If this is the module that came with the devkit then it should boot into linux when powered on assuming you don't hit any keys during the boot loader stage.
If its just booting to the u-boot prompt it would be helpful to see the full ... - HB 02:06 PM Software Development: RE: Problems with the first time configuration
- Hi Jonathan,
I'm using now TeraTerminal, my serial port is working OK and I got in the U-Boot prompt, I checked the configuration of the Network Adapter of the Virtual Machine and is set up like a Bridge.
I tried to ping the VM I...
05/24/2016
- AB 07:27 PM Software Development: RE: PRU_gpioToggle example fails sometimes
- So, I've been playing around with the example code more to try to get the interrupt wait() and clear() to work.
This is how it is supposed to work: - AB 02:00 PM Software Development: RE: PRU_gpioToggle example fails sometimes
- In @static int LOCAL_exampleInit ( unsigned short prunum )@ of PRU_gpioToggle.c we need to have
- AB 11:42 AM Software Development: RE: PRU_gpioToggle example fails sometimes
- So this is strange. I modified the gpioToggle code to have the following:
- JC 01:30 PM Software Development: RE: Problems with the first time configuration
- Hector Bojorquez wrote at https://support.criticallink.com/redmine/projects/arm9-platforms/activity?from=2016-05-24:
> Hi everyone, I'm starting with the PROFIBUS development kit and I was trying to follow the starter guide until I came... - JC 01:20 PM Software Development: RE: Starter Guide: "Boot the MityDSP-L138 up into linux." - How?
- Hector, I'm going to respond in your other forum post.
https://support.criticallink.com/redmine/boards/10/topics/4825 - HB 12:05 PM Software Development: RE: Starter Guide: "Boot the MityDSP-L138 up into linux." - How?
- Hi everyone, I'm starting with the PROFIBUS development kit and I was trying to follow the starter guide until I came to the _*boot up in linux*_ step just like Jeff
I have Enabled the serial port from VBox and configured the port mod...
05/23/2016
- AB 11:11 PM Software Development: RE: PRU_gpioToggle example fails sometimes
- This seems to be the same as one of the issues that Jonathan Cormier observed in the topic that you linked. E.g., "gpioToggle test passed when i just ran it. Not sure why." whereas he had earlier posted that it failed.
As for trying t... - BD 10:30 PM Software Development: RE: PRU_gpioToggle example fails sometimes
- Andrew,
Another user was able to successfully run the demos on the MityDSP-L138, but perhaps they didn't test things as strenuously as you did.
<https://support.criticallink.com/redmine/boards/10/topics/4026>
Regarding point 2, ... - I'm having multiple issues with the PRU example PRU_gpioToggle. In short, it seems like some read/write operations to memory mapped locations are not always executing properly. The two problem spots are the following:
1) In the exampl...
05/20/2016
- HB 05:10 PM Software Development: RE: Problems with the first time configuration
- Hi Jonathan,
I imagine that you always work with more experienced users :D , but I'm just starting with this kind of systems, I will be waiting anxiously for the post.
Meanwhile I'll check all about the MDK updating and about my s... - JC 04:53 PM Software Development: RE: Problems with the first time configuration
- Hector,
Sorry about all this. I am going to see if someone can add some detail to the Quick start guide about initial power on. Hopefully will work on it on Monday.
In the meantime we usually use putty or teraterm for accessing t... - HB 04:35 PM Software Development: RE: Problems with the first time configuration
- Thanks for the quick response,
??Running debug in this case has probably tried to run the program on the VM. This HelloWorld file was compiled for the MityDSP so will only run on the MityDSP platform.??
I see, that has a lot ... - JC 02:39 PM Software Development: RE: Problems with the first time configuration
- Hector Bojorquez wrote:
> Hi everyone!
> ...
Running debug in this case has probably tried to run the program on the VM. This HelloWorld file was compiled for the MityDSP so will only run on the MityDSP platform.
>
> ...
You must u... - Hi everyone!
I have just acquired the PROFIBUS development kit from Critical Link, I was trying to put it on following the Starter guide steps in Critical Link support page,
I updated and installed the GCC, the MDK and the CDT, I con...
05/13/2016
- AB 03:34 PM Software Development: RE: PRU svn authentication failed
- "Password for '(null)' GNOME keyring:" seemed suspect, so i searched on that.
I had to do the following, and then it worked:
@rm ~/.gnome2/keyrings/*@ - AB 03:28 PM Software Development: RE: PRU svn authentication failed
- I pinged google just to make sure the internet connection is up. Here's what I get:
@
mitydsp@mitydsp-dev:~$ cd SVN
mitydsp@mitydsp-dev:~/SVN$ ping www.google.com
PING www.google.com (216.58.192.196) 56(84) bytes of data.
64 bytes... - JC 03:15 PM Software Development: RE: PRU svn authentication failed
- Bob Duke wrote:
> Andrew, I had no problems with this command:
> ...
I've updated the wiki page [[Using_PRU]], to reflect the need to use the username anonymous. - BD 03:14 PM Software Development: RE: PRU svn authentication failed
- Andrew, I had no problems with this command:
- JC 03:09 PM Software Development: RE: PRU svn authentication failed
- Found this TI wiki. It appears that you must use the username anonymous with a blank password.
http://processors.wiki.ti.com/index.php/PRU_Linux_Application_Loader#Installing_the_Kernel_Driver - When running the following:
svn co https://gforge.ti.com/svn/pru_sw/trunk pru_sw
I get the message
"... Could not authenticate to server: rejected Basic challenge (https://gforge.ti.com)"
Previously, the following worked, but...
05/12/2016
- DS 10:38 AM Software Development: RE: Emulator stops working very often.
- We generally try to do as little as possible in main(). It should launch an initialization task and you would work from there.
If you do not need to debug initialization, sometimes it may be beneficial to allow the code to run (not h...
05/10/2016
- EM 02:48 PM Software Development: RE: Cannot run multiple times my ARM/DSP application
- Various small errors contributed to the problem. things seem to work better now. I can send & Recv 3 messages and I discovered the debugMsg print queue as well.
05/09/2016
- EM 12:32 PM Software Development: RE: Cannot run multiple times my ARM/DSP application
- I think these are the files you need. Basically, just the HelloWorld files. Let me know if you need anything else.
- MW 11:52 AM Software Development: RE: Cannot run multiple times my ARM/DSP application
- Would it be possible for you to post a copy of your example code, including the BIOS configuration files?
If you want you could send it directly via email offline...
-Mike
- EM 11:48 AM Software Development: RE: Cannot run multiple times my ARM/DSP application
- I have something like this:
// Create the object used to send messages to the DSP
lpMessageOutbound = new tcIPCOutbound((char*)"DSPMSGQ0");
// Wait for the DSP to finish initialization (really just waiting for first message, wh... - EM 11:30 AM Software Development: RE: Cannot run multiple times my ARM/DSP application
- I know this is an old thread, but I am having similar issues. This is the first time I have head about the "ReturnBuffer()" call. I searched the Hello World could and could not find any reference to it. The header file is not really cl...
05/06/2016
- EL 08:41 AM Software Development: RE: iproute2 for SocketCAN with 3.2 Kernel
- Thanks. After running ip link set eth0 1000000, I can see the can0 interface listed.
The next step in the wiki is to send a message with cansend. Do you happen to have a binary of canutils as well?
Either way, I will try to write ...
05/04/2016
- GG 06:16 PM Software Development: RE: iproute2 for SocketCAN with 3.2 Kernel
- Hi Ed,
We've run into a similar problem here and rebuilt the package ourselves.
As a quick fix I've attached the package file. Install with - The iproute2 utility for linux 3.2 seems to be unavailable from opkg. I am therefore unable to run the example in the wiki at https://support.criticallink.com/redmine/projects/indio/wiki/CAN_support, which I was hoping to use to prove th...
- EM 05:34 PM Software Development: RE: Emulator stops working very often.
- Is there some sort really basic initialization that I am missing? Are there interrupts occurring that I am suppose to handle even for the most basic "Hello World" type of app. It can not step through something as simple as :
int main(i...