Activity

From 04/16/2016 to 05/15/2016

03:34 PM Software Development: RE: PRU svn authentication failed: "Password for '(null)' GNOME keyring:" seemed suspect, so i searched on that.
I had to do the following, and then ... Andrew Bean
03:28 PM Software Development: RE: PRU svn authentication failed: I pinged google just to make sure the internet connection is up. Here's what I get:
@
mitydsp@mitydsp-dev:~$ cd S... Andrew Bean
03:15 PM Software Development: RE: PRU svn authentication failed: Bob Duke wrote:
> Andrew, I had no problems with this command:
> [...]
>
> Can you please try again and if you h... Jonathan Cormier
03:14 PM Software Development: RE: PRU svn authentication failed: Andrew, I had no problems with this command:... Bob Duke
03:09 PM Software Development: RE: PRU svn authentication failed: Found this TI wiki. It appears that you must use the username anonymous with a blank password.
http://processors.wi... Jonathan Cormier
03:05 PM Software Development: PRU svn authentication failed: When running the following:
svn co https://gforge.ti.com/svn/pru_sw/trunk pru_sw
I get the message
"... Coul... Andrew Bean

10:38 AM Software Development: RE: Emulator stops working very often.: We generally try to do as little as possible in main(). It should launch an initialization task and you would work f... Dave Stehlik

02:48 PM Software Development: RE: Cannot run multiple times my ARM/DSP application: Various small errors contributed to the problem. things seem to work better now. I can send & Recv 3 messages and I d... Edwin McKay

12:32 PM Software Development: RE: Cannot run multiple times my ARM/DSP application: I think these are the files you need. Basically, just the HelloWorld files. Let me know if you need anything else. Edwin McKay
11:52 AM Software Development: RE: Cannot run multiple times my ARM/DSP application: Would it be possible for you to post a copy of your example code, including the BIOS configuration files?
If you w... Michael Williamson
11:48 AM Software Development: RE: Cannot run multiple times my ARM/DSP application: I have something like this:
// Create the object used to send messages to the DSP
lpMessageOutbound = new tcIPC... Edwin McKay
11:30 AM Software Development: RE: Cannot run multiple times my ARM/DSP application: I know this is an old thread, but I am having similar issues. This is the first time I have head about the "ReturnBu... Edwin McKay

08:41 AM Software Development: RE: iproute2 for SocketCAN with 3.2 Kernel: Thanks. After running ip link set eth0 1000000, I can see the can0 interface listed.

The next step in the wiki is... edward lambert

06:16 PM Software Development: RE: iproute2 for SocketCAN with 3.2 Kernel: Hi Ed,
We've run into a similar problem here and rebuilt the package ourselves.
As a quick fix I've attached ... Gregory Gluszek
03:48 AM Software Development: iproute2 for SocketCAN with 3.2 Kernel: The iproute2 utility for linux 3.2 seems to be unavailable from opkg. I am therefore unable to run the example in the... edward lambert
05:34 PM Software Development: RE: Emulator stops working very often.: Is there some sort really basic initialization that I am missing? Are there interrupts occurring that I am suppose t... Edwin McKay

01:20 PM Software Development: RE: ifup / ifdown Equivalent for systemd: Ben,
Your concern is valid and I don't have a direct answer now. The @ip@ command is the correct one to use to con... Bob Duke
11:04 AM Software Development: RE: Linker memory layout.: I think these errors have been over come. I'm using the 8000 tcf file. I am able to run the program and debug a littl... Edwin McKay
10:59 AM Software Development: RE: Linker memory layout.: Edwin, Did you figure this out?
Some comments from Dave here:
> Could it be trying to use two .cmd files?
> At... Jonathan Cormier
09:14 AM Software Development: DDR configuration for AISgen on MityDSP-L138: We are trying to flash our firmware on the MityDSP-L138 to run code from the DDR. We are using the AISGen tool from T... Friedrich Feichtinger

10:59 AM Software Development: RE: WFI and Bluetoth support: I am looking at the Redpine Signals RS9113-NZB.
We may be using it in anther product Using the TI arm file system th... steven poffenbarger
10:33 AM Software Development: RE: WFI and Bluetoth support: Steven,
We've integrated multiple Wifi/BT chipsets with our products. In most cases we have to integrate an extern... Bob Duke
08:56 AM Software Development: WFI and Bluetoth support: Does the Yocto file system support the TI or other vendors wifi and bluetooth on the DBric3?
what is the interface t... steven poffenbarger

10:49 AM Software Development: Emulator stops working very often.: I continually get these sort of messages while I try to step through the DSP code. Some times I can debug for a few m... Edwin McKay

04:58 PM Software Development: RE: No Prompt from Uboot: Thanks. You got it.
Only way to be sure was to cut the i2c traces on the carrier. Biked over to my partners and go... Ian St. John
09:02 AM Software Development: RE: No Prompt from Uboot (update): Ian St. John wrote:
> ALSO note that I am worried about the message "error reading I2C Configuration Block". Is th... Jonathan Cormier
12:37 AM Software Development: RE: No Prompt from Uboot: I don't have either a second (working) module or a standard carrier board. We couldn't afford them when we started an... Ian St. John

05:39 PM Software Development: RE: Any special thing to get new ObjectXXX to work.: Hi Edwin,
Your project should have a .tcf file. This should define how memory is configured and how large your he... Gregory Gluszek
04:35 PM Software Development: RE: No Prompt from Uboot: Ian,
Can you let us know if the behavior changes when this module is used in the Industrial IO Development Board (... Alexander Block
03:34 PM Software Development: RE: No Prompt from Uboot (baahhh): Well, it worked for two or three runs. Now it hangs on the uart initialization? Thinks that the uart is busy with out... Ian St. John
12:46 PM Software Development: RE: No Prompt from Uboot (update): Imported and ran UBL to CCS 6.1.2. Changed only DEVICE_UART_PERIPHNUM to 1 from 2 in devices_uart.h to get UBL messag... Ian St. John

12:51 PM Software Development: RE: No Prompt from Uboot: Mike,
Thanks for the description. I think your confusion is more about not understanding why it doesn't work (like... Ian St. John
08:17 AM Software Development: RE: No Prompt from Uboot: Hello,
So I'm struggling a bit to get the full picture of what is going on.
Are you saying that you are running... Michael Williamson

06:21 PM Software Development: RE: No Prompt from Uboot: Uboot won't load (SPI mem = 0, i.e. says file too big on load of UBL)
Backup code was NOT the solution. Recent code ... Ian St. John
02:09 PM Software Development: RE: No Prompt from Uboot (update): I found and old backup where SpiWriter still works. Got my application code loaded into SPI NOR flash. I will try to ... Ian St. John

Also available in: Atom

Go to top

Mity CPU Platforms » MityDSP-L138 (ARM9 Based Platforms)