Project

General

Profile

Activity

From 04/17/2016 to 05/16/2016

05/13/2016

03:34 PM Software Development: RE: PRU svn authentication failed
"Password for '(null)' GNOME keyring:" seemed suspect, so i searched on that.
I had to do the following, and then ...
Andrew Bean
03:28 PM Software Development: RE: PRU svn authentication failed
I pinged google just to make sure the internet connection is up. Here's what I get:
@
mitydsp@mitydsp-dev:~$ cd S...
Andrew Bean
03:15 PM Software Development: RE: PRU svn authentication failed
Bob Duke wrote:
> Andrew, I had no problems with this command:
> [...]
>
> Can you please try again and if you h...
Jonathan Cormier
03:14 PM Software Development: RE: PRU svn authentication failed
Andrew, I had no problems with this command:... Bob Duke
03:09 PM Software Development: RE: PRU svn authentication failed
Found this TI wiki. It appears that you must use the username anonymous with a blank password.
http://processors.wi...
Jonathan Cormier
03:05 PM Software Development: PRU svn authentication failed
When running the following:
svn co https://gforge.ti.com/svn/pru_sw/trunk pru_sw
I get the message
"... Coul...
Andrew Bean

05/12/2016

10:38 AM Software Development: RE: Emulator stops working very often.
We generally try to do as little as possible in main(). It should launch an initialization task and you would work f... Dave Stehlik

05/10/2016

02:48 PM Software Development: RE: Cannot run multiple times my ARM/DSP application
Various small errors contributed to the problem. things seem to work better now. I can send & Recv 3 messages and I d... Edwin McKay

05/09/2016

12:32 PM Software Development: RE: Cannot run multiple times my ARM/DSP application
I think these are the files you need. Basically, just the HelloWorld files. Let me know if you need anything else. Edwin McKay
11:52 AM Software Development: RE: Cannot run multiple times my ARM/DSP application
Would it be possible for you to post a copy of your example code, including the BIOS configuration files?
If you w...
Michael Williamson
11:48 AM Software Development: RE: Cannot run multiple times my ARM/DSP application
I have something like this:
// Create the object used to send messages to the DSP
lpMessageOutbound = new tcIPC...
Edwin McKay
11:30 AM Software Development: RE: Cannot run multiple times my ARM/DSP application
I know this is an old thread, but I am having similar issues. This is the first time I have head about the "ReturnBu... Edwin McKay

05/06/2016

08:41 AM Software Development: RE: iproute2 for SocketCAN with 3.2 Kernel
Thanks. After running ip link set eth0 1000000, I can see the can0 interface listed.

The next step in the wiki is...
edward lambert

05/04/2016

06:16 PM Software Development: RE: iproute2 for SocketCAN with 3.2 Kernel
Hi Ed,
We've run into a similar problem here and rebuilt the package ourselves.
As a quick fix I've attached ...
Gregory Gluszek
03:48 AM Software Development: iproute2 for SocketCAN with 3.2 Kernel
The iproute2 utility for linux 3.2 seems to be unavailable from opkg. I am therefore unable to run the example in the... edward lambert
05:34 PM Software Development: RE: Emulator stops working very often.
Is there some sort really basic initialization that I am missing? Are there interrupts occurring that I am suppose t... Edwin McKay

04/26/2016

01:20 PM Software Development: RE: ifup / ifdown Equivalent for systemd
Ben,
Your concern is valid and I don't have a direct answer now. The @ip@ command is the correct one to use to con...
Bob Duke
11:04 AM Software Development: RE: Linker memory layout.
I think these errors have been over come. I'm using the 8000 tcf file. I am able to run the program and debug a littl... Edwin McKay
10:59 AM Software Development: RE: Linker memory layout.
Edwin, Did you figure this out?
Some comments from Dave here:
> Could it be trying to use two .cmd files?
> At...
Jonathan Cormier
09:14 AM Software Development: DDR configuration for AISgen on MityDSP-L138
We are trying to flash our firmware on the MityDSP-L138 to run code from the DDR. We are using the AISGen tool from T... Friedrich Feichtinger

04/22/2016

10:59 AM Software Development: RE: WFI and Bluetoth support
I am looking at the Redpine Signals RS9113-NZB.
We may be using it in anther product Using the TI arm file system th...
steven poffenbarger
10:33 AM Software Development: RE: WFI and Bluetoth support
Steven,
We've integrated multiple Wifi/BT chipsets with our products. In most cases we have to integrate an extern...
Bob Duke
08:56 AM Software Development: WFI and Bluetoth support
Does the Yocto file system support the TI or other vendors wifi and bluetooth on the DBric3?
what is the interface t...
steven poffenbarger

04/21/2016

10:49 AM Software Development: Emulator stops working very often.
I continually get these sort of messages while I try to step through the DSP code. Some times I can debug for a few m... Edwin McKay

04/20/2016

04:58 PM Software Development: RE: No Prompt from Uboot
Thanks. You got it.
Only way to be sure was to cut the i2c traces on the carrier. Biked over to my partners and go...
Ian St. John
09:02 AM Software Development: RE: No Prompt from Uboot (update)
Ian St. John wrote:
> ALSO note that I am worried about the message "error reading I2C Configuration Block". Is th...
Jonathan Cormier
12:37 AM Software Development: RE: No Prompt from Uboot
I don't have either a second (working) module or a standard carrier board. We couldn't afford them when we started an... Ian St. John

04/19/2016

05:39 PM Software Development: RE: Any special thing to get new ObjectXXX to work.
Hi Edwin,
Your project should have a .tcf file. This should define how memory is configured and how large your he...
Gregory Gluszek
04:35 PM Software Development: RE: No Prompt from Uboot
Ian,
Can you let us know if the behavior changes when this module is used in the Industrial IO Development Board (...
Alexander Block
03:34 PM Software Development: RE: No Prompt from Uboot (baahhh)
Well, it worked for two or three runs. Now it hangs on the uart initialization? Thinks that the uart is busy with out... Ian St. John
12:46 PM Software Development: RE: No Prompt from Uboot (update)
Imported and ran UBL to CCS 6.1.2. Changed only DEVICE_UART_PERIPHNUM to 1 from 2 in devices_uart.h to get UBL messag... Ian St. John

04/17/2016

12:51 PM Software Development: RE: No Prompt from Uboot
Mike,
Thanks for the description. I think your confusion is more about not understanding why it doesn't work (like...
Ian St. John
08:17 AM Software Development: RE: No Prompt from Uboot
Hello,
So I'm struggling a bit to get the full picture of what is going on.
Are you saying that you are running...
Michael Williamson
 

Also available in: Atom

Go to top
Add picture from clipboard (Maximum size: 1 GB)